BEFORE DIALING INTO YOUR ISP,
go to Command tool from start>all program>.accerorries>Dos Prompt
or Start > Run type “cmd” enter then type ” Netstat-ARN “then enter again.
-----------------------------------------------------------------------------
Active Routes:
Network Address Netmask Gateway Address Interface Metric
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1
255.255.255.255 255.255.255.255 255.255.255.255 0.0.0.0 1
Route Table
Active Connections
Proto Local Address Foreign Address State
--------------------------------------------------------------------------------
If you see anything else, there might be a problem (more on that later).
Now dial into your ISP, once you are connected;
go back to the MS-DOS Prompt and run the same command as before
netstat -arn, this time it will look similar to the following (without
dotted lines).
------------------------------------------------------------------------------------- Active Routes: Network Address Netmask Gateway Address Interface Metric Route Table Active Connections Proto Local Address Foreign Address State -------------------------------------------------------------------------------- What you are seeing in the first section (Active Routes) under the heading of The numbers are divided into four dot notations, the first three should be To make sure that the first three notation are as they should be, we will run --------------------------------------------------------------------------------------- Tracing route to /www.motion.net [207.239.117.112]over a maximum of 30 hops: ------------------------------------------------------------------------------------------ You will see that on lines with the 1 and 2 the first three notations of the If everything matches like above, you can almost breath easier. Another thing ------------------------------------------------------------------------------------------- Now just because everything reported out like we expected (and demonstrated What can you do? Well some anti-virus software will detect some trojans. Other options Display protocol statistics and current TCP/IP network connections. -a.. Display all connections and listening ports.
0.0.0.0 0.0.0.0 216.1.104.70 216.1.104.70 1
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1
216.1.104.0 255.255.255.0 216.1.104.70 216.1.104.70 1
216.1.104.70 255.255.255.255 127.0.0.1 127.0.0.1 1
216.1.104.255 255.255.255.255 216.1.104.70 216.1.104.70 1
224.0.0.0 224.0.0.0 216.1.104.70 216.1.104.70 1
255.255.255.255 255.255.255.255 216.1.104.70 216.1.104.70 1
TCP 0.0.0.0:0 0.0.0.0:0 LISTENING
TCP 216.1.104.70:137 0.0.0.0:0 LISTENING
TCP 216.1.104.70:138 0.0.0.0:0 LISTENING
TCP 216.1.104.70:139 0.0.0.0:0 LISTENING
UDP 216.1.104.70:137 *:*
Network Address are some additional lines. The only ones that should be there
are ones belonging to your ISP (more on that later). In the second section
(Route Table) under Local Address you are seeing the IP address that your ISP
assigned you (in this example 216.1.104.70).
the same for both sets, while in this case the .70 is the unique number
assigned for THIS session. Next time you dial in that number will more than
likely be different.
one more command from the MS-DOS window.
From the MS-DOS Prompt type tracert /www.yourispwebsite.com or .net
or whatever it ends in. Following is an example of the output you should see.
1 128 ms 2084 ms 102 ms chat-port.motion.net [216.1.104.4]
2 115 ms 188 ms 117 ms chat-core.motion.net [216.1.104.1]
3 108 ms 116 ms 119 ms www.motion.net [207.239.117.112]
Trace complete.
address match with what we saw above, which is a good thing. If it does not,
then some further investigation is needed.
which should you should check is programs launched during startup. To find
these, Click start/programs/startup, look at what shows up. You should be
able to recognize everything there, if not, once again more investigation is
needed.
above) we still are not out of the woods. How is this so, you ask? Do you use
Netmeeting? Do you get on IRC (Internet Relay Chat)? Or any other program
that makes use of the Internet. Have you every recieved an email with an
attachment that ended in .exe? The list goes on and on, basically anything
that you run could have become infected with a trojan. What this means, is
the program appears to do what you expect, but also does just a little more.
This little more could be blasting ebay.com or one of the other sites that
CNNlive was talking about.
Another (tedious) thing is to start each of these "extra" Internet programs
one at a time and go through the last two steps above, looking at the routes
and connection the program uses. However, the tricky part will be figuring
out where to tracert to in order to find out if the addresses you see in
step 2 are "safe" or not. I should forewarn you, that running tracert after
tracert, after tracert might be considered "improper" by your ISP. The steps
outlined above may not work exactly as I have stated depending upon your ISP,
but with a true ISP it should work. Finally, this advise comes with NO
warranty and by following my "hints' you implicitly release me from ANY and
ALL liability which you may incur.
Netstat [-a] [-e] [-n] [-s] [-p proto] [-r] [intervals]
-e.. Display Ethernet statistics. This may be combined with the -s option.
-n.. Diplays address and port numbers in the numerical form.
-p proto..Shows connections for the protocol specified by proto; proto may be
TCP or UDP. If used with the -s option to display per-protocol statistics,
proto may be TCP, UDP, of IP.
-r.. Display the routing table.
-s.. Display per-protocol statistics. By default, statistics are shown for TCP
UDP and IP; the -p option may be used to specify a subset of the default
interval..Redisplay selected statistics, pausing intervals seconds between each
display. If omitted. netstat will print the current configuration information
once
Tidak ada komentar:
Posting Komentar